Pentru a identifica cu exactitate piesa compatibila cu modelul dumneavoastra de centrala viessmann trebuie sa ne comunicati seria centralei termice. Toate fotografiile prezentate pot sa nu fie actualizate la infatisarea actuala a produselor. Conform normelor ISCIR, orice interventie asupra centralei termice se poate realiza numai de catre o firma autorizata in vederea intretinerii, reparatiilor si verificarilor. Realizarea montajului de catre persoane sau firme neautorizate, se efectueaza pe propria raspundere, firma noastra fiind exonerata de orice obligatie. Nerespectarea regulilor de montaj conform specificatiior producatorului duce obligatoriu la pierderea garantiei.
|Published (Last):||12 August 2013|
|PDF File Size:||8.75 Mb|
|ePub File Size:||15.86 Mb|
|Price:||Free* [*Free Regsitration Required]|
Switching between summer and winter operation has priority over the heating only time control optional when this is connected to the boiler. Page 8: Maintenance If the problem remains after two attempts at resetting, contact the Ferroli Service Centre. For other faults, refer to section 3. Before calling a Ferroli service engineer, check that the problem is not due to there being no gas or electricity, or low system pressure. The installation room must be sufficiently well ventilated to prevent any dangerous conditions from forming in the event of even slight gas leakage.
This safety standard is required by the EEC Directive no. Reference should be made to BS, for methods of filling and making up sealed systems. Page Water Treatment The connecting kits shown in fig. An existing service pipe must not be used whitout prior consultation with the local Gas supplier.
Page Flue System The current standards and local regulations must be observed. It should be noted that only Ferroli flue system and accessories should be used on this appliance, as per BS and C. Page 16 DOMIcompact F 24 B Restrictor This appliance is factory fitted with the correct restrictor for use with a standard mm concentric flue terminal of less than 1mtr. For different flueing applications choose the correct size restrictor from the tables below. To change the restrictor please follow the instructions below, shown in figure 9.
Numerous accessories are available on request to meet the various installation requirements. Connect the flue to the boiler, positioning the seals correctly. Flue seals should be lubricated with a silicone type grease to prevent damage grease not sup Page 19 3. Check that the total calculated loss is less than or equal to 55 equivalent metres, i.
Terminal Position B - minimum distance mm - may be a nuisance as plume could obscure window. Page Condensate Outlet Connection Connection to collective flues or single flues with natural draught If you are then going to connect the DOMIcompact F 24 B boiler to a collective flue or a single flue with natural draught, the flue must be expressly designed by professionally qualified technical personnel in conformity with the standards and rules in force.
The minimum pipe diameter required is 22 mm, a trap has already been fitted to the appliance with a flexible hose to facilitate the connection to the condensate discharge pipe. Page Service And Maintenance All adjustment and conversion operations must be carried out by a Qualified and trained engineer such as a Ferroli Service. Page 26 DOMIcompact F 24 B Adjusting burner pressure Since this unit has flame modulation, there are two fixed pressure settings: the minimum and maximum, which must be as stated in the technical data chart according to the type of gas.
Turn the heating tem- perature control knob ref. Page 29 DOMIcompact F 24 B Before carrying out any operation inside the boiler, disconnect the electrical power and isolate the gas supply. Special care must be taken over all the seals pertaining to the sealed chamber gaskets, cable clamps, etc.
In the event of a fault within the boiler, the display will show the relevant code. There are faults that cause shutdown faults from F1 to F3 : in order to restore operation it requires the operator to press RESET for 1 second ref.
DOMIPROJECT F24 D
Switching between summer and winter operation has priority over the heating only time control optional when this is connected to the boiler. Page 8: Maintenance If the problem remains after two attempts at resetting, contact the Ferroli Service Centre. For other faults, refer to section 3. Before calling a Ferroli service engineer, check that the problem is not due to there being no gas or electricity, or low system pressure.
Ventilator centrale termice Ferroli Domiproject F 24, Fereasy F 24, Domicompact , Divatech, Divatop