Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies.
|Published (Last):||4 October 2016|
|PDF File Size:||12.12 Mb|
|ePub File Size:||1.80 Mb|
|Price:||Free* [*Free Regsitration Required]|
September If an FCC declaration of conformity marking is pr e sent on the board, the followi Intended Audience The Product Guide is intended for technically qualif ied personnel. It is not intended for gener al audiences. Information Layout The ch Feature Summary Manufacturing Options Desktop B Table 1 summarizes the major features of the desktop board. Table 1. Table 2. If your memory modules do not support SPD, you will see a notification to this effect on the screen at power up.
The BIOS wi Table 6. Table 7. Green On LAN link is establishe d. Blinking LAN activity is occurring. See Figure 25 on page 4 9 and Figure 26 on page 50 for the location of the power connectors.
Fan Connectors The desktop boards have a 4-pin processor fan header. While in the S3 sleep state, the computer will appear to be off. When signaled by a wake-up device or event, the system quickly retu rns to its last known awake state. PME Wake Intel DGAG - page 29 Installing and Replacing Desktop Board Components 29 Chassis and Component Certifications Ensure that the chassis and certain components; such as the power supply, peripheral drives, wiring, and cables; are components certified for the country or market where used.
Agency certification marks on the product are proof of certif ication. Typical produ The suitability of this product for other ap Disconnect the computer from its power source before performing the procedures de scribed here. Failure to disconnect the power before you open the computer can result in personal injury Remove the plastic protective socket cover from th e load plate. Do not discard the protective socket cover. Always replace the socket cover if the processor is removed from the socket see Figure 9, E.
E Figure 9. Remove the Protective Socket Cover 5. Remove the processor from the protective Hold the processor with your thumb and index finge rs oriented as shown in Figure Make sure fingers align to the socket cutouts see Figure 11, F. Align notches see Figure 11, G with the socket see Figure 11, H. Lower the pr ocessor straight down without tilting or sl OM Figure Observe the precautions in "Before You Begin" on page Turn off all peripheral devices connected to the computer.
Turn off the computer and disconnect the AC power cord. Turn off the computer. Remove the AC power cord from the computer. Remove the computer? If the card is not fully seated in the PCI Express connector, an electrical short Figure 20 shows the correct installation of the cable. Either end of the cable can be connected to the SATA drive or the connector on the board. For correct cable function: 1. Observe the precaution i Figure 22 shows the location of the internal headers.
Table 9 shows the pin assignments for the front panel audio header. Table 9. Table 10 shows the pin assignments for the USB 2. Table Connect chassis fan cables to the 3-pin fan headers. Connecting 2x10 Power Supply Cables The 2x12 main power conne Figure 26 shows the location of the power connectors. OM 2X12 1 2 Figure Connecting 2x12 Power Supply Cables 1. Observe the precautions in "Before You Begin" on Moving the jumper with the power on may result in unreliable computer operation.
Figure 28 shows the location of the desktop boar Intel DGAG - page 53 Installing and Replacing Desktop Board Components 53 Clearing Passwords This procedure assumes that the board is installe d in the computer and the configuration jumper block is set to normal mode. Turn off the comput Poor audio quality ma y occur if passive non-amplified speakers are connected to this output. Figure 29 shows the location of the ba When the computer is not plugged into a wall socket, the battery ha s an estimated life of three years.
When the computer is plugged in, the standby current from the power supply extends the li fe of th Utilizzare solo pile uguali o di tipo equivalente a quelle consigliate dal produttore. Per disfarsi delle pile usate, seguire le istruzioni del produttore.
Bat eri sepatutnya dikitar semula jika boleh. Pel upusan bateri terpakai mestilah me matuhi peraturan al am sekitar tempatan. The utility available from the Web provides a simple method for creating a bootable flash memory update floppy th The following steps expl ain how to recover the BIOS if an update fails. The following procedure uses recovery mode fo r the Setup program.
See page 52 for more information on Setup modes. NOTE Bec Using both hardware and sof What is unique about security has to do with understanding who "fri ends" a nd adversaries are. Once this is done, the removable media should be stored in a secure location. This permits the owner of the system to control initialization of the TPM and create all the passwords a No copies of this Emergency Recovery Token file should remain on the system. If a copy remains on the system, it could b e used to compromise the secu rity of the platform.
Create a Ba Failure to do this can result in personal injury or equipment damage. Some ci rcuitry on the desktop board can co Table 17 gives an explanation of the BIOS error messages. If no memory was removed, then memory may be bad. Memory Size Increased Memory size has increased since the last boot.
If no memory was added, there may be a pr oblem with the sys Include s adjacent UL file Questi sono tra gli altri: - disegni tecnici Intel.
Intel® Desktop Board D915GAV
Intel D915GAV Manuals & User Guides