HUAWEI CDMA BTS 3606 PDF

Mikasa The alarm box is correctly installed according to the design. The sectional area is 35 cables VL: Diagonally fasten them to a 45 N-m in-lbas shown in Figure Tighten the bolts at the front face of the cabinet. Page cdmw The packing case is in good condition. Lead the bolts through the lower support.

Author:Shakazilkree Grorisar
Country:Jordan
Language:English (Spanish)
Genre:Relationship
Published (Last):22 March 2007
Pages:439
PDF File Size:6.68 Mb
ePub File Size:14.56 Mb
ISBN:447-5-27937-493-7
Downloads:74568
Price:Free* [*Free Regsitration Required]
Uploader:Megore



Tojora Page 43 5 M6x20 combined screw Figure Installing a cabinet on the antistatic floor Figure hts how to install a BTS cabinet on the floor without sufficient bearing capacity. For the proper storage, use and disposal of this product, national laws and regulations must be observed. Watch out for the sharp edges on the RF fan panel during btx installation of RF cables lest it hurt your fingers. Other Cables The power cable and the grounding cable are routed straight and bundled neatly. Thus, you do not need to install these cables on site.

Otherwise, the equipment will suffer severe damages. The color of the coat must be the same as or similar to that of the cabinet. It is divided into six chapters: GND cables for indoor cabling racks and for outdoor cabling racks. The last section also explains how to install cabinet assemblies on the cement floor without sufficient bearing capacity.

Leveling the lower support See section 2. This manual also for: Lead the bolts through the lower support. Connect one end of the cable to the working ground of the EAC. All Rights Reserved Huuawei part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co.

Select and release the primary mouse button without Click moving the pointer. When installing the RF cable, connect unused connectors to matching load and secure them. Diagonally fasten them to a 45 N-m in-lbas shown in Figure They are used for the convenience of installation description. That is, 1 m 39 in. Place the support below the antistatic floor. Figure Installing a board 2 Tighten the screws clockwise on the front panel, as shown in Figure The power cable and the grounding cable are routed straight and bundled neatly.

Conducting Insulation Test To conduct an insulation test, proceed as follows: Route the alarm cables coming in from the other side of the enclosure through the cabling holes on both sides of the 8-E1 module and then to the respective slots.

O 2 Configuration Hhawei O 2 refers to an omni cell with two carriers. Lead the cables into their corresponding cable-fixing troughs. Note, Comment, Tip, Knowhow, Thought: Please feel free to contact our local office or company headquarters. Page 70 — Distributing Protection Grounding Cables Procedure To carry out the power-on check of power module, proceed bst follows: The engineering supervisor does not submit self-test report on quality of the engineering hardware.

Figure shows RF cable connections, indicated by blue lines. Normally, the fan box is installed upon delivery. Means a complementary description.

If the power supply is on during the operation, do not brs the binding posts with the adjustable wrench or the screwdriver. The letters A, B, C as shown in Figure are not cable labels.

The panel is clean without obvious damage. Insert the boards according to the names on the relevant nameplates to avoid any mistake. Chapter 4 Installing Cables Thus, you do not need to install these cables on site. Huawei BTS Installation Manual Anchor bolt for the floor d expansion bolt d height-lock bolt first in the middle, then on both sides To huwwei the support, proceed as follows: Make sure that all the power modules are well connected with the backplanes, and that other boards and modules such as the CTRM and CHPA are not inserted in the slots of the backplanes.

Page 15 The packing case is in good condition. Tighten the bolts on the huawek. Page of 93 Go. Wooden cases are generally used to pack heavy objects like racks, batteries, and so on.

Cut the tapes along the seams of the carton cover using a knife. Installing Other Functional Modules Normally, the fan box is installed upon delivery. For the specific method, see section 2. Remove four bolts and one gasket that connect the antistatic floor and the support. Feed back the situation to the local Huawei Representative Office.

TOP Related Posts.

SUNDER GUTKA PDF

BTS3900 GSM

Mouse operation Action Description Press and hold the primary mouse button left mouse Select button by default. Hardware quality control supervision. Its advanced features include priority call, call hold, late entry, dynamic grouping, and fallback mode. Tighten the bolts at the front face of the cabinet. Procedure To carry out the power-on check of power module, proceed as follows: Wooden cases are generally used to pack heavy objects like racks, batteries, and so on.

CVSA OUT OF SERVICE CRITERIA PDF

Huawei BTS3606 Installation Manual

The power cable and the grounding cable are routed straight and bundled neatly. Enter text from picture: The depth of the hole must range from 52 mm 2 in. Page 43 5 M6x20 combined screw Figure Installing a cabinet on the antistatic floor Figure shows how to install a BTS cabinet on the floor without sufficient bearing capacity. This chapter describes how to install and use these two types of DDF. No field installation of the fan box is required.

N.PISKUNOV - DIFFERENTIAL AND INTEGRAL CALCULUS PDF

HUAWEI CDMA BTS 3606 PDF

Tojora Page 43 5 M6x20 combined screw Figure Installing a cabinet on the antistatic floor Figure hts how to install a BTS cabinet on the floor without sufficient bearing capacity. For the proper storage, use and disposal of this product, national laws and regulations must be observed. Watch out for the sharp edges on the RF fan panel during btx installation of RF cables lest it hurt your fingers. Other Cables The power cable and the grounding cable are routed straight and bundled neatly. Thus, you do not need to install these cables on site. Otherwise, the equipment will suffer severe damages. The color of the coat must be the same as or similar to that of the cabinet.

Related Articles